Whirlpool Washer WTW4800BQ1 Manual

The Whirlpool WTW4800BQ1 is a top-loading high-efficiency washer featuring an impeller-based wash system, multiple cycles for various fabrics, electronic controls with LED display, automatic temperature control, deep water wash option, and a durable stainless steel wash basket. It is designed for residential use and operates on a standard 120V, 15-amp circuit. Below are key sections for safety, features, installation, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Water & Drain 7. Using Wash Cycles 8. Special Features 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Electronic control panel with LED display, Stainless Steel Wash Basket, Impeller Wash System, Lid Lock, Water Inlet Valves, Drain Pump, and Leveling Legs.

Feature	Description
Electronic Controls	LED display for cycle selection, time remaining, and status
Stainless Steel Basket	Durable, rust-resistant wash basket
Impeller Wash System	High-efficiency cleaning with less water
Lid Lock	Safety feature that locks during cycle operation
Water Inlet Valves	Hot and cold water connections with automatic fill
Drain Pump	Pumps water out through drain hose
Leveling Legs	Adjustable front legs for stability
Deep Water Wash Option	Extra water for heavily soiled loads
Automatic Temperature Control	Mixes hot and cold water to selected temperature
Multiple Cycles	Includes Normal, Heavy Duty, Delicates, Quick Wash, and more

Installation

Unpack and inspect contents. Place on a solid, level floor near water supply and drain.

Remove shipping materials: Take off cardboard base and foam blocks. Remove shipping bolts from rear.
Connect water supply: Attach hot and cold hoses to corresponding faucets (red=hot, blue=cold).
Connect drain hose: Place hose into standpipe or laundry tub; secure with provided hook if needed.
Level the washer: Adjust front leveling legs until washer is stable and does not rock.
Plug into grounded 120V outlet.

WARNING! Do not remove shipping bolts until washer is in final position. Ensure water connections are tight to prevent leaks.

First-Time Setup

Before first use, run a cleaning cycle.

Connect power and water supply.
Open lid and ensure basket is empty.
Add 1 cup of liquid bleach to the basket (not dispenser).
Select "Clean Washer" cycle (or "Normal" with hot water if no dedicated cycle).
Press START and allow cycle to complete.
Wipe interior and exterior with a damp cloth.

CAUTION! Use only HE (High-Efficiency) detergent. Overuse of detergent can cause oversudsing.

Specifications

Model: WTW4800BQ1
Type: Top-Load High-Efficiency Washer
Capacity: 4.3 cu. ft.
Control: Electronic with LED Display
Wash System: Impeller
Basket Material: Stainless Steel
Water Connections: Hot & Cold (120°F max inlet temp)
Electrical: 120V, 60Hz, 15 Amp
Dimensions (HxWxD): Approximately 43" x 27" x 28"
Cycle Options: Normal, Heavy Duty, Delicates, Quick Wash, Bulky Items, Rinse & Spin, Drain & Spin

Controls and Settings

Control Panel: POWER, CYCLE SELECTION KNOB, OPTIONS buttons (Deep Water, Extra Rinse), TEMPERATURE, SPIN SPEED, START/PAUSE.

Cycle Knob: Turn to select desired wash cycle. LED will indicate selection.

Options: DEEP WATER (adds more water), EXTRA RINSE (adds an additional rinse cycle).

Temperature: Select from Cold, Cool, Warm, Hot for wash and rinse.

Spin Speed: Select from No Spin, Low, Medium, High, Max for final spin.

Start/Pause: Press to begin cycle; press again to pause. Lid locks when cycle starts.

Connecting Water & Drain

Water Supply: Use provided hoses. Drain: Use provided drain hose.

Turn off water faucets before connecting hoses.
Connect hot (red) and cold (blue) hoses to corresponding faucets and washer inlet valves.
Hand-tighten; avoid over-tightening.
Place drain hose into a standpipe (minimum 36" high) or laundry tub.
Secure hose to prevent slipping.

Tip: Run water through hoses into a bucket first to flush out debris before connecting to washer.

Using Wash Cycles

Supports various fabrics and soil levels.

Load laundry: Do not overload. Clothes should move freely.
Add detergent: Pour HE detergent into detergent dispenser. Use recommended amount.
Add bleach/fabric softener: Use designated dispensers if available.
Select cycle: Turn knob to desired cycle (e.g., Normal for cottons).
Select options: Press DEEP WATER or EXTRA RINSE if needed.
Select temperature and spin speed.
Close lid and press START.
Cycle completes: Signal sounds. Lid unlocks after basket stops spinning.

WARNING! Do not open lid during spin cycle. Wait for lid lock to release.

Special Features

Deep Water Wash: Provides more water for heavily soiled loads. Extra Rinse: Adds a rinse cycle for sensitive skin or detergent residue. Quick Wash: 15-minute cycle for lightly soiled loads. Clean Washer Cycle: Periodically run to clean interior and remove odors (use affresh® tablet or bleach).

Care & Cleaning

Unplug before cleaning. Wipe exterior with soft, damp cloth. Clean interior by running "Clean Washer" cycle monthly with affresh® washer cleaner or liquid bleach. Clean detergent dispenser monthly by removing and rinsing under warm water. Keep area around washer clean and dry.

CAUTION! Do not use abrasive cleaners or solvents. Do not spray water directly on controls.

Regulatory Information

UL Listed. Complies with U.S. Federal energy standards. Manufactured for household use. Copyright © Whirlpool Corporation. All trademarks used herein are the property of Whirlpool Corporation or their respective owners. For support, visit www.whirlpool.com or contact 1-800-253-1301.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Washer won't start	Lid open, no power, pause active	Close lid securely; check power outlet and cord; press START/PAUSE.
No water filling	Water supply off, kinked hoses	Turn on hot/cold faucets; straighten inlet hoses.
Water won't drain	Drain hose clogged/kinked	Check hose for obstructions; ensure proper height (min 36").
Excessive vibration/noise	Unlevel floor, shipping bolts not removed	Level washer; ensure all shipping bolts and materials are removed.
Leaking water	Loose hose connections, over-sudsing	Tighten hose connections; use less HE detergent.
Clothes too wet after spin	Load unbalanced, low spin speed selected	Redistribute load evenly; select higher spin speed.

Reset: Unplug washer for 1 minute, then plug back in.

Service: 1-800-253-1301; www.whirlpool.com