Whirlpool Washer Model WTW4800BQ0 Manual

The Whirlpool WTW4800BQ0 is a top-loading washer with a 4.3 cu. ft. capacity, featuring an IMPELLA™ wash system, 12 wash cycles, 5 soil levels, 5 spin speeds, and 5 temperature settings. It includes options like Deep Water Wash, Extra Rinse, and a Delay Wash feature. This manual covers safety information, installation, operation, cycle guides, maintenance, and troubleshooting for optimal performance.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Utilities 7. Using Wash Cycles 8. Special Features 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Control Panel, Lid, IMPELLA™ Wash Plate, Agitator, Dispenser Drawer, Drain Pump Filter, Leveling Legs, Power Cord, Water Inlet Hoses.

Feature	Description
IMPELLA™ Wash System	Dual-action washing with an impeller and agitator for thorough cleaning
4.3 cu. ft. Capacity	Large capacity for bulky items like comforters
12 Wash Cycles	Includes Normal, Heavy Duty, Delicates, Quick Wash, and more
5 Soil Levels	Light, Normal, Heavy, Extra Heavy, Max Extract
5 Spin Speeds	Adjustable for different fabric types
5 Temperature Settings	Cold, Cool, Warm, Hot, Extra Hot
Deep Water Wash	Option for more water during wash and rinse
Extra Rinse	Adds an additional rinse cycle
Delay Wash	Delays start time up to 12 hours
Cycle Status Lights	Indicates current stage of wash cycle

Installation

Unpack and inspect contents. Place on a solid, level floor.

Remove shipping materials: Take off cardboard base, tape, and foam blocks from inside the tub.
Install drain hose: Connect to standpipe or laundry sink; secure with hose clamp.
Connect water supply: Attach hot and cold water inlet hoses to faucets and washer.
Level the washer: Adjust the leveling legs to prevent vibration and noise.
Plug into a grounded 120V, 60Hz outlet.

WARNING! Do not remove the black rubber drain plug from the back of the washer. Ensure all connections are tight to prevent leaks.

First-Time Setup

Before first use, run a cleaning cycle.

Ensure washer is properly installed and leveled.
Turn on water supply faucets completely.
Plug in the washer.
Add 1 cup of liquid bleach to the bleach dispenser.
Select the "Clean Washer" cycle (or "Normal" cycle with hot water if no dedicated cycle).
Press START/PAUSE to begin. Allow cycle to complete.

CAUTION! Do not load laundry during the cleaning cycle. Keep lid closed during operation.

Specifications

Model: WTW4800BQ0
Type: Top-Load Washer
Capacity: 4.3 cubic feet
Color: White
Control Type: Electronic with dial and buttons
Wash System: IMPELLA™ (Impeller + Agitator)
Voltage: 120V AC, 60Hz
Water Supply Pressure: 20-120 psi (min/max)
Dimensions (HxWxD): Approximately 43.5" x 27" x 27.5"
Shipping Weight: Approximately 125 lbs

Controls and Settings

Control Panel: Cycle Selector Knob, START/PAUSE Button, OPTIONS Buttons (Soil Level, Spin Speed, Temp, Deep Water, Extra Rinse, Delay Wash), Status Lights.

Cycle Selector: Turn knob to choose from 12 cycles: Normal, Heavy Duty, Delicates, Quick Wash, Bulky/Sheets, Active Wear, Sanitize, Whites, Deep Clean, Rinse & Spin, Spin Only, Clean Washer.

Options: After selecting a cycle, use option buttons to customize: Soil Level (Light to Max Extract), Spin Speed (Delicate to High), Water Temp (Cold to Extra Hot), Deep Water Wash (On/Off), Extra Rinse (On/Off), Delay Wash (1-12 hrs).

Status Lights: Indicate cycle stage: Wash, Rinse, Spin, End of Cycle.

Connecting Utilities

Water Supply: Connect hot (left) and cold (right) hoses. Drain: Secure drain hose to standpipe (minimum 39" height) or laundry sink. Power: Use dedicated 120V outlet.

Turn off water faucets before connecting hoses.
Use only new hoses; do not reuse old ones.
Ensure drain hose is not kinked and is secured to prevent slipping.
Plug power cord directly into wall outlet; do not use an extension cord.

Tip: Check for leaks at hose connections after first use.

Using Wash Cycles

Follow these steps for optimal washing.

Load laundry: Do not overload. Mix large and small items.
Add detergent: Pour into main wash compartment of dispenser. Use HE detergent.
Add additives: Bleach to bleach compartment, fabric softener to softener compartment.
Select cycle: Turn knob to desired cycle.
Set options: Press option buttons to adjust soil, spin, temp, etc.
Start: Close lid and press START/PAUSE. Lid locks during operation.
Pause/Stop: Press START/PAUSE once to pause (lid unlocks after a few seconds). Press and hold for 3 seconds to cancel cycle.

WARNING! Do not force lid open during operation. Wait for lid lock to release after pausing.

Special Features

Deep Water Wash: Provides more water for heavily soiled loads or bulky items. Extra Rinse: Adds a rinse for sensitive skin or detergent residue. Delay Wash: Sets a start time up to 12 hours later. Clean Washer Cycle: Runs a maintenance cycle to clean the tub (use monthly).

Care & Cleaning

Unplug before cleaning. Wipe exterior with soft, damp cloth. Clean dispenser drawer monthly: Pull out, rinse under water. Clean drain pump filter (located behind lower access panel) every 3-6 months to remove lint/debris. Run "Clean Washer" cycle monthly with washer cleaner or bleach.

CAUTION! Do not use abrasive cleaners or solvents. Keep control panel dry.

Regulatory Information

This appliance complies with FCC Part 15 Rules. Operation is subject to the condition that it does not cause harmful interference. Copyright © Whirlpool Corporation. All rights reserved. For support, visit www.whirlpool.com or contact 1-800-253-1301.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Washer won't start	Lid open, no power, paused	Close lid firmly; check power outlet and cord; press START/PAUSE.
No water filling	Water supply off, kinked hoses	Turn on both hot/cold faucets; straighten inlet hoses.
Excessive vibration/noise	Unlevel floor, shipping bolts not removed	Level washer; ensure all shipping materials are removed.
Water leaks	Loose hose connections, over-sudsing	Tighten hoses; use less HE detergent.
Clothes too wet after spin	Low spin speed selected, overload	Select higher spin speed; reduce load size.
Error codes (e.g., F1, F5)	Sensor or drain issue	Unplug for 5 minutes, replug. If persists, call service.

Reset: Unplug washer for 1 minute, then plug back in.

Service: 1-800-253-1301; www.whirlpool.com